[/url]Image

How to install 2009 2010 2011 Mazda 6 aftermarket gps navigation system

Welcome to share your installation experience and ideas on those car radio dvd gps stereo device

Moderators: Jammy, admin

User avatar
Andy
Posts: 307
Joined: Fri Dec 11, 2015 6:24 am
Contact:

How to install 2009 2010 2011 Mazda 6 aftermarket gps navigation system

Postby Andy » Fri Dec 25, 2015 6:08 am

Nowadays installing new dvds for cars is not only to keep up with the trend,but also become a very necessary thing for drivers are increasing at a surprising speed,it means that driving become more disturbed than before.So when you have the desire to buy a fashionable car DVD player for your Mazda 6 of 2009-2011,you go to the exact shop and see various kind of stereo radio and feel confused which one to choose for your car.Don’t worry,if your dashboard of car radio is the same with this one:audio system after installation,aftermarket radio gps nav system with bluetooth music of 2009 2010 2011 Mazda 6,then it is suitable for your car and can be installed without problems.

Next I will show you detailed installation operations for Mazda 6.
1.Unclip and remove the cup holder panel in the center console
1.png
1.png (246.62 KiB) Viewed 3673 times

2.Unscrew and remove the shift knob,then remove the small pocket panel
2.png
2.png (207.43 KiB) Viewed 3673 times

3.Unclip and remove trim panels(total 2) beside the shift knob
3.png
3.png (227.44 KiB) Viewed 3673 times

4.Fasten and remove center trim panel,if you feel hard to do it,then you operate next step first
4.png
4.png (214.87 KiB) Viewed 3673 times

5.Press in shifter fasten trigger and pull shifter down,make sure a brake on! After this,you can remove the center trim panel
5.png
5.png (200.8 KiB) Viewed 3673 times

6.Remove two Phillips screws on each side of the center consoles,then remove center consoles
6.png
6.png (251.67 KiB) Viewed 3673 times

7.Remove left screw and right bolt
7.png
7.png (218.69 KiB) Viewed 3673 times

8.Fasten and remove the vent panel including the hazard switch above the original player
8.png
8.png (162 KiB) Viewed 3673 times

9.Remove these two screws with a screwdriver
9.png
9.png (213.13 KiB) Viewed 3673 times

10.Take out original stereo autoradio and disconnect cables with the help of suitable tools
10.png
10.png (187.07 KiB) Viewed 3673 times

10-1.png
10-1.png (221.41 KiB) Viewed 3673 times

11.Unclip this bolt and make most fine connected here and firm by that bolt
11.png
11.png (188.88 KiB) Viewed 3673 times

11-1.png
11-1.png (194.95 KiB) Viewed 3673 times

12.Plug these plugs as the picture show

13.After cables are settled to right positions,put new unit into the space
14.Make all set-aside panels back to its original place and firm corresponding screws and shift knob
All installation work has been finished.Before you are begin to install Mazda 6 aftermarket gps navigation, there are some tips to mind:

1.Make sure that you have accomplished car’s parking series before you begin any work
2.Plesae do not use any strong chemicals or cleansers clean the unit
3.When you are installing the wiring, make it as neatly as possible, because the space for it is very small
4.Please don’t remove the GPS SD card when the power is on

To be honest,most of the installation process of radio gps nav system for Mazda series are same in a large proportion,of course it may have some difference during your work,but don’t worry,this is normal and all will be solved only if you make adequate preparation before you start up your removal,such as read installation guide carefully and act as it say,or visit some related websites,for example, and you can also ask dealers for help.
3.png
3.png (227.44 KiB) Viewed 3673 times
7.png
7.png (218.69 KiB) Viewed 3673 times
Attachments
12.png
12.png (247.29 KiB) Viewed 3673 times



Return to “Car Radio DVD GPS Stereo”

Who is online

Users browsing this forum: No registered users and 3 guests